Procedure

Last Updated : Oct 30, 2026 |
Prolog information
Metadata
Keywords:
  1. Connect to the ASP Host server using the services port connection.
  2. Initiate a session to the ASP host using a Secure Shell (SSH) client e.g., PuTTY.
  3. Authenticate using the existing custadm credentials or craft if EASG is enabled.
  4. Execute the following CLI command: configNetwork.
  5. Follow the script prompts:
    1. Type y to continue if the connection is via services port.
    2. Type n to continue (OOBM configuration is not part of this procedure).
    3. Enter the number of bridges to configure: 1 or 2.
      ADDITIONAL INFORMATION:
      Note:
      Script automatically detects existing configuration and will display the current value between parentheses.
    4. To configure bridge0 (Management/VM Bridge), type 3 for 10/25G LACP bond.
    5. Select the LACP Data Units exchange rate. For this example, 0 will be selected for fast.
    6. Select the LACP load balance HASH policy. For this example, 1 will be selected for layer3+4.
    7. Type n to continue (VLAN configuration is not part of this procedure).
      ADDITIONAL INFORMATION:
      Note:
      Script automatically detects existing configuration and will display the current value between parentheses. If VLAN configuration is detected, to retain current configuration, simply press Enter without making any changes to keep existing setup.
    8. Press Enter key (7 times) until prompt displays Continue with these values? y=continue/n=retry/q=quit (n). If satisfied with current selections type y.
      ADDITIONAL INFORMATION:
      Note:
      Although multiple changes at the same time are supported by the network script, IP address changes are not part of this procedure.
      Figure: Example output when a VLAN has not been configured previously
      [custadm@asp130-r660xs-20841 ~]$ configNetwork
      ===================  Server Network Configuration  ===================
      Note: you should run this command from the console or services port
            After making configuration changes running VMs should be restarted.

      Do you want to continue (y/n) y

      The configured or default value is displayed in parentheses ().
      Press 'enter' to accept it, enter 'd' to delete it or type a new value.

      Connect this server to an Out Of Band Management network (OOBM)? y/n (n)
      Create an OOBM bridge for VMs use? y/n (n)

      ========== Network Bridge Configuration ==========
      Configure network bridges for management and VMs.

      Do you want to configure 1 or 2 bridges? (1) 1

       === Configuring bridge0 (Management/VM Bridge) ===
       0) 1G direct interface
       1) 1G active/backup bond
       2) 10/25G direct interface
       3) 10/25G LACP bond
       4) 10/25G active/backup bond

      Select configuration for bridge0: (0) 3
      Configuring 10/25G LACP bond for bridge0
       0) fast
       1) slow
       Select the LACP Data Units exchange rate (): 0
       0) layer2
       1) layer3+4
      Select the LACP load balance HASH policy (): 1
      Using available 10/25G ports for bond: ens1f0np0, ens1f1np1

       Do you want to configure a Management/VM's VLAN? y/n (n) n
      Enter Server hostname (asp130-r660xs-20841.acp.avaya.com):
      Enter Server IPv4 (192.168.208.41):
      Enter Server netmask or /prefix (/26):
      Enter the IPv4 default gateway (192.168.208.1):
      Do you want to configure IPv6? y/n (n)
      Enter comma separated DNS servers (192.168.209.21):
      Enter comma separated IPv4 domain search (acp.avaya.com):
       Continue with these values? y=continue/n=retry/q=quit (n) y

      Bridge bridge0: initialization successful
      Bond: initialization successful
       Bond port bond0-port1 ens1f0np0 initialization successful
      Bond port bond0-port2 ens1f1np1 initialization successful
      Bridge bridge0: IP initialization successful.
      Figure: Example output when a VLAN has been configured previously
      [custadm@asp130-r660xs-20841 ~]$ configNetwork
      ===================  Server Network Configuration  ===================
      Note: you should run this command from the console or services port
            After making configuration changes running VMs should be restarted.

      Do you want to continue (y/n) y

      The configured or default value is displayed in parentheses ().
      Press 'enter' to accept it, enter 'd' to delete it or type a new value.

      Connect this server to an Out Of Band Management network (OOBM)? y/n (n)
      Create an OOBM bridge for VMs use? y/n (n)

      ========== Network Bridge Configuration ==========
      Configure network bridges for management and VMs.

      Do you want to configure 1 or 2 bridges? (1)

      === Configuring bridge0 (Management/VM Bridge) ===
       0) 1G direct interface
       1) 1G active/backup bond
       2) 10/25G direct interface
       3) 10/25G LACP bond
       4) 10/25G active/backup bond

      Select configuration for bridge0: (0) 3
      Configuring 10/25G LACP bond for bridge0
       0) fast
       1) slow

      Select the LACP Data Units exchange rate (): 0
       0) layer2
       1) layer3+4

       Select the LACP load balance HASH policy (): 1
      Using available 10/25G ports for bond: ens1f0np0, ens1f1np1

      Do you want to configure a Management/VM's VLAN? y/n (y)
      Enter the Management/VM's VLAN ID (1010):
      Configure additional VLANs on the bridge0 (Management/VM's) ports? y/n (n)
      Enter Server hostname (asp130-r660xs-20841.acp.avaya.com):
      Enter Server IPv4 (192.168.208.41):
      Enter Server netmask or /prefix (/26):
      Enter the IPv4 default gateway (192.168.208.1):
      Do you want to configure IPv6? y/n (n)
      Enter comma separated DNS servers (10.129.209.21):
      Enter comma separated IPv4 domain search (acp.avaya.com):
       Continue with these values? y=continue/n=retry/q=quit (n) y

       Bridge bridge0: initialization successful
      Bond: initialization successful
      Bond VLAN 1010 on bridge0-port initialization successful
      Bond port bond0-port1 ens1f0np0 initialization successful
      Bond port bond0-port2 ens1f1np1 initialization successful
      Bridge bridge0: IP initialization successful.
  6. Execute the following CLI command for bond configuration validation: nmcli con
    ADDITIONAL INFORMATION:
    Figure: Example output: LACP Bond configuration without VLAN
    [custadm@asp130-r660xs-20841 ~]$ nmcli connection
    NAME             UUID                                  TYPE      DEVICE
     Mgmt_VM_Network  e19f2a52-53e8-4d9b-93ec-dcd2eab34d86  bridge    bridge0
    Services         73e59eb5-3cd3-4c62-b34e-8fdf900617b9  ethernet  eno8403
    bond0-port1      a933239e-1274-4a8d-be83-b31a28388ac6  ethernet  ens1f0np0
    bond0-port2      3e9b59c0-f0af-4e78-b569-b81d83bc845c  ethernet  ens1f1np1
    bridge0-port     97b7facb-e07d-4a8c-8d2f-ae9476eea612  bond      bond0
    eno12399         853e573e-4693-4d9d-9cb9-24444a8b4dea  ethernet  --
    eno12409         33b09f62-fe3c-4525-83c7-d58eb0a64c98  ethernet  --
    eno12419         1a1c223f-6aa7-47f7-a0bf-97b675cacb14  ethernet  --
    eno12429         2ac9c2fe-9637-467b-8ef1-fa0f4010a2a1  ethernet  --
    eno8303          6d541615-24f0-4878-8786-e95ff6f5920d  ethernet  --
    ens1f0np0        b7a8628e-0120-4925-a92d-8965eadfa881  ethernet  --
    ens1f1np1        3e1115e6-a617-4b9d-bf98-402bb0e33582  ethernet  --


     
    Figure: Example output: LACP Bond configuration with VLAN

    [custadm@asp130-r660xs-20841 ~]$ nmcli connection
    NAME             UUID                                  TYPE      DEVICE
     Mgmt_VM_Network  27a53466-8b78-4d80-8df6-24c4ba0857e5  bridge    bridge0
    Services         73e59eb5-3cd3-4c62-b34e-8fdf900617b9  ethernet  eno8403
    bond0            b396fbb4-bce4-4c6e-9696-b4bac1e13422  bond      bond0
    bond0-port1      f7c5e628-6136-466c-ab22-3759fa8397c7  ethernet  ens1f0np0
    bond0-port2      3af96828-123d-4647-b856-9edaaf09546b  ethernet  ens1f1np1
    bridge0-port     fe3d87c3-9809-4ebf-960b-25934bb2ca07  vlan      bond0.1010
    eno12399         853e573e-4693-4d9d-9cb9-24444a8b4dea  ethernet  --
    eno12409         33b09f62-fe3c-4525-83c7-d58eb0a64c98  ethernet  --
    eno12419         1a1c223f-6aa7-47f7-a0bf-97b675cacb14  ethernet  --
    eno12429         2ac9c2fe-9637-467b-8ef1-fa0f4010a2a1  ethernet  --
    eno8303          6d541615-24f0-4878-8786-e95ff6f5920d  ethernet  --
    ens1f0np0        b7a8628e-0120-4925-a92d-8965eadfa881  ethernet  --
    ens1f1np1        3e1115e6-a617-4b9d-bf98-402bb0e33582  ethernet  --
     
Related links
Adding a bond using the network configuration script