Administering the AAR Digit Analysis Table for UDP

Last Updated : Oct 12, 2021 |
Prolog information
Metadata
Keywords:
  1. Enter change aar analysis n, where n is the number of the AAR Digit Analysis Table.
  2. In the Dialed String column, type the numbers that the system compares to the number that the user dials.
    ADDITIONAL INFORMATION:
    You can also type *, a lower case x, or an upper case X as wildcard characters.
    The system uses the dialed string that most closely matches the number that the user dials. For example, if a user dials 297-1234, and the AAR Digit Analysis Table contains two dialed strings of 297-1 and 297-123, the system uses the dialed string 297-123 as the match.
    When the system compares a user-dialed number with an entry in the Dialed String column that is an exact match and an entry in the Dialed String column with one or more wildcard characters, the system chooses the exact match. For example, if a user dials 424, and the AAR Digit Analysis Table contains two dialed strings of 424 and X24, the system uses the dialed string 424 as the match.
  3. In the Min column, type the minimum number of user-dialed digits that the system uses to compare with the matching pattern in the Matching Pattern column.
  4. In the Max column, type the maximum number of user-dialed digits that the system uses to compare with the matching pattern in the Matching Pattern column.
  5. In the Route Pattern column, type the route information that you want the server to use for the dialed string.
    ADDITIONAL INFORMATION:
    Perform one of the following actions:
    • To specify the route index number that you established on the Partition Routing Table screen, type a value from p1 to p2000.
    • To specify the route pattern that the system uses to route the call, type a number from 1 to 640.
    • To specify the route pattern that the system uses to route the call, type a number from 1 to 999 or 1 to 2000. If you are using the S8300D or S8300E server, you can configure a maximum of 999 route patterns. If you are using the HP DL360 G7, or Dell R610, sever, you can configure a maximum of 2000 route patterns.
    • If RHNPA translations are required for the corresponding dialed string, type a value from r1 to r32 to specify the remote home numbering plan.
    • To designate node number routing, type node.
    • To block the call, type deny.
  6. In the Call Type column, type the call type that is associated with each dialed string.
    ADDITIONAL INFORMATION:
    The call types indicate the numbering requirements on different trunk networks. Perform one of the following actions:
    • For regular AAR calls, type aar.
    • If the Route Index contains public network ISDN trunks that require the international type of number encodings, type intl.
    • If the Route Index contains public network ISDN trunks that require an unknown type of number encodings, type pubu.
    • To specify the ISDN Private Number Plan (PNP) number formats, type lev0, lev1, or lev2.
    • For a UDP numbering plan where extensions are passed (rather than full public network or private-network numbers), type unku.
      For more information on ISDN Numbering-Private, see Administering Avaya Aura® Communication Manager.
      The table describes the ISDN protocols.
      ISDN protocols
      Call type
      Numbering plan identifier
      Type of numbering
      aar
      E.164(1)
      national(2)
      intl
      E.164(1)
      international(1)
      pubu
      E.164(1)
      unknown(0)
      lev0
      PNP(9)
      local(4)
      lev1
      PNP(9)
      Regional Level 1(2)
      lev3
      PNP(9)
      Regional Level 2(1)
      unku
      unknown (0)
      unkown (0)
  7. In the Node Number column, type the number of the destination node in a private network if you use node number routing or Distributed Communication System (DCS).
  8. Use the ANI Req column only if the Request Incoming ANI (non-AAR/ARS) field is set to
    ADDITIONAL INFORMATION:
    If the Request Incoming ANI (non-AAR/ARS) field is set to
    • If you require ANI on incoming R2-MFC or Russian MF ANI calls, type y.
    • If you do not require ANI on incoming R2-MFC or Russian MF ANI calls, type n.
    • If the Allow ANI Restriction on AAR/ARS field is set to
    • , the system drops a call on a Russian shuttle trunk or a Russian rotary trunk if the ANI request fails. For calls on other types of trunks, the system processes an
    • .
The Percent Full column displays the percent of the allocated system memory that is used by AAR and ARS. You cannot change this field.
  • Select Enter to save your changes.
    • Related links
    Uniform Dial Plan administration
    Uniform Dial Plan administration