Abbreviated Dialing

The IP DECT station uses the Abbreviated Dialing List feature access codes to dial the station, group and system abbreviated dial lists (as administered per station).

Analog – Generic

The IP DECT station can be treated as an analog station in terms of feature interactions.

Analog Disconnect

Communication Manager supports the Analog Disconnect with dial tone after 10 seconds feature for IP DECT.

Announcement

The IP DECT station initiates the Announcement feature to record an announcement by dialing the Announcement feature access code.

Attendant

The IP DECT station reaches an Attendant by dialing the Attendant feature access code.

Automatic Alternate Routing

The IP DECT station initiates an Automatic Alternate Routing (AAR) call by dialing the AAR feature access code.

Automatic Call Back

The IP DECT station initiates or receives an Automatic Call Back (ACB) call by dialing the ACB feature access code.

Automatic Call Distribution

The IP DECT station uses the various Automatic Call Distribution (ACD) features. The ACD features can be activated by dialing the following ACD feature access codes:

• After Call Work

• Assist

• Auto-In

• Aux Work

• Login

• Logout

• Manual-in

• Service Observing Listen Only

• Service Observing Listen/Talk

• Service Observing No Talk

• Add Agent Skill

• Remove Agent Skill

• Remote Logout of Agent

These features do not provide ACD-related display update to the IP DECT telephones. If the IP DECT telephone is out of a coverage area, is turned off, or has a low battery, Communication Manager has no knowledge in these scenarios. As a result, Communication Manager cannot accept service from the IP DECT telephones.

Automatic Route Selection

The IP DECT station initiates an Automatic Route Selection (ARS) call by dialing the ARS feature access code.

Bridged appearance

The IP DECT station can be an analog-bridged appearance on another station, or can be administered as a bridged appearance (analog or regular) of a station.

The bridge appearance status LEDs reflects the status of the IP DECT station. The IP DECT station can bridge calls as in any other bridge of a directly connected wired station. The MWI of the station can be set to the principal extension or the bridged extension.

Call Admission Control

The IP DECT configuration supports Call Admission Control bandwidth limits between any pair of IP network regions.

Call Coverage

When coverage is administered for the IP DECT station, if the station (Ring No Answer, Subscriber Absent, or Busy) does not answer the call, the X-mobile station sends calls to coverage. The IP DECT station can be a coverage point and supports the IP DECT reject feature.

If the IP DECT station is out of system, silent charging, or the user presses the reject button, IP DECT system drops the alerting call. If the station has no answer coverage, the call immediately goes to coverage. If the station is a coverage point, the call immediately progress to the next coverage point. In both the cases, the call does not drop and the caller continues to receive ringback.

If the IP DECT station is a bridge, the reject button will have the above affect. The coverage path used is that of the principal, not the IP DECT station.

Call forwarding

The IP DECT station can activate and deactivate all options for call forwarding, extended call forwarding, and enhanced call forwarding using the various call forwarding feature access codes. The remote station state can be used to determine if call forwarding criteria is met. If the remote station is busy, the criteria is met. If the remote station does not answer the call, Ring No Answer criteria is met. The IP DECT can be the station that is call forwarded to and supports the IP DECT reject feature.

If the IP DECT is out of system, silent charging, or the user presses the reject button, IP DECT system drops the alerting call. If the station has no answer forwarding, the call immediately forwards. Coverage after forwarding may still take place. In both the cases, the call does not drop and the caller can continue to receive ringback.

If the IP DECT station is a bridge, the reject button will have the above effect. The forwarding used is that of the principal, not the IP DECT station.

Call Park or Answer Back

The IP DECT station can park its current call after a flash operation by using the Call Park feature access code. The IP DECT station can answer a parked call by using the Answer Back feature access code.

Call Pickup

The IP DECT station can be in a Call Pickup Group and use the Call Pickup, Directed Call Pickup, Directed Group Call Pickup, and Extended Group Call Pickup feature access codes.

Pickup groups containing IP DECT can be in the Extended Groups. As a result, IP DECT handsets can pickup calls from other pickup groups in the same way the analog-wired stations can.

Call Shuttle

If the IP DECT feature is administered as a call shuttle, the station is alerted through call waiting tone when another incoming call arrives for it while the IP DECT station is on a call. The IP DECT station can accept the second call automatically through a flash operation. This puts the first party on soft hold. Subsequent flash operations shuttle between the second and first parties result in clearing the current call and recalling the IP DECT station to attempt to reconnect the soft held party.

Call Vectoring

The IP DECT station can change the values of variables used in the Call Vectoring feature. The values can be changed by dialing the following Call Vectoring or Prompting feature access codes:

• Converse Data Return Code

• Vector Variables 1-9

Call Waiting

When a call arrives for the IP DECT station and Call Waiting is administered, Call Waiting Tone is applied as defined by the operations of Communication Manager.

CAS Remote Hold or Answer Hold-Unhold

The IP DECT station uses the CAS Remote Hold or Answer Hold-Unhold feature access code to put a call on hard hold and to retrieve a call from hard hold.

CDR Account Code

The IP DECT station enters a CDR Account Code by dialing the CDR Account Code feature access code.

Change COR

The IP DECT station can change its COR by dialing the Change COR feature access code.

Change Coverage

The IP DECT station can change its coverage path by dialing the Change Coverage feature access code.

Codec selection

Communication Manager use the codecs administered on the IP Codec Set screen corresponding to the IP Network Region for the H.323 signaling group pointing to IP DECT system and negotiate the codecs to use with IP DECT system as in H.323.

Conference

The flash operation is sent by pressing the R-Key on the IP DECT handset. If the IP DECT initiates a second call by a previous flash operation and the third party answer the second call, then a flash operation conference all three parties. If the IP DECT initiates another flash operation, the IP DECT drops the last added party. If the IP DECT telephone drops from the conference and hence is now idle, the remaining parties on the conference call stay connected.

To activate a conference you need to enable the Allow Conference via Flash field on the Feature-Related System Parameters screen, otherwise the flash operation (R-key) puts the active call on hold and brings up the held call to active state.

Connection Failover with Master Base Station

Upon a connection failover during an ongoing IP DECT to IP DECT call, the secondary base station takes over. However the very first call made from either of the IP DECT extension shall not succeed. From then on, any further call from either of the IP DECT will be successful.

Connection Preservation for Branch Gateways Failover and Failback

Connection preservation for Branch Gateways in Failover and Failback does not support H.323 trunks. As a result, this feature does not work for IP DECT configurations.

Contact Closure

The IP DECT station performs various Contact Closure features by dialing the Contact Closure feature access codes.

Coverage Answer Group

The IP DECT station can be a member of a coverage answer group (as a primary appearance only).

EC500

The IP DECT can change a cell phone number associated with the EC500 feature by dialing the EC500 Self Administration feature access code.

The IP DECT can activate or deactivate the enhanced EC500 feature by dialing the EC500 Self Administration feature access code.

Emergency Calling

The IP DECT can reach the attendant in an emergency by dialing the Emergency Access to Attendant feature access code.

Extended numbering plan

The IP DECT station supports an extended numbering plan.

Facility restriction

The IP DECT system is marked with a specific Class of Restriction (COR) and Class of Service (COS), which affect toll calling and general calling permissions and restrictions.

Facility test call

The IP DECT system initiates a facility test call for a testing a trunk by dialing the Facility Test Call feature access code.

Flash Access Code

The IP DECT system sends a flash signal to the central office switch by dialing the Flash feature access code.

Group Control Restrict

The IP DECT system changes the restriction levels for all users within a given class of restriction by dialing the Group Control Restrict Activation or Deactivation feature access codes. To do this, you must have console permissions assigned to your Class of Service (COS) for the station.

Hold and Enquiry Call

The IP DECT system places an existing call on hold and makes a new enquiry call using the flash hook operation. The Hold feature behaves in a similar manner as an analog telephone. When the enquiry call is over or has not reached successfully, the IP DECT can return to the original call. Music-on-hold applies, when administered, to the held station.

Hospitality features

The IP DECT system uses the various Hospitality features. You must enable the Hospitality features for the following Hospitality feature access codes to work:

• Automatic Wakeup Call

• Housekeeping Status (Client Room)

• Housekeeping Status (Station)

• Verify Wakeup Announcement

• Voice Do Not Disturb

Hunting

The IP DECT station can be a member of a hunt group (as a primary, not a bridge). When the WT is turned off or out of range, the WT is treated as busy and Communication Manager will hunt to the next member.

The IP DECT station makes itself busy or available for hunt group functionality by dialing the Hunt Group Busy Activation or Deactivation feature access codes.

The IP DECT station can be a part of a station hunting chain as administered through the Hunt-to-Station field on the Station screen.

Inter-Gateway Alternate Routing

IP DECT system configurations supports Inter-Gateway Alternate Routing (IGAR) configurations.

ISDN call

The IP DECT station places an ISDN call without using ARS, AAR or UDP by dialing the ISDN feature access code.

Last Number Dialed

The IP DECT station can redial the last number dialed by the station by dialing the Last Number Dialed feature access code.

Malicious Call Trace

The IP DECT station can start and stop a Malicious Call Trace by dialing the Malicious Call Trace Activation or Deactivation feature access codes.

Meet-me Conference

The IP DECT station can dial into a Meet-me Conference.

The IP DECT station can change the Meet-me Conference access code by dialing the Meet-me Conference Access Code Change feature access code.

Multiple Precedence and Preemption

The IP DECT system uses the various Multiple Precedence and Preemption (MLPP) features. You must enable the MLPP features for the following MLPP feature access codes to work:

• Precedence Calling

• Worldwide Number and Dial Plan Precedence Access Codes for

  • Flash override preemption level

  • Flash preemption level

  • Immediate preemption level

  • Priority preemption level

  • Routine preemption level

Per Call CPN

The IP DECT system blocks or unblocks CPN on a trunk call by dialing the Per Call CPN Blocking or Unblocking Code feature access codes.

PIN Checking

The IP DECT system invokes the PIN Checking feature by dialing the following feature access codes:

• PIN Checking for Private Calls

• PIN Checking for Private Calls Using ARS

• PIN Checking for Private Calls Using AAR

Posted Messages

The IP DECT system invokes or cancels a posted message by dialing the Posted Messages Activation or Deactivation feature access codes.

Priority Calling

The IP DECT system initiates a priority call by dialing the Priority Calling feature access code.

Program AD lists

The IP DECT system initiates the Program AD List feature by dialing the Program feature access code.

The IP DECT system initiates the Abbreviated Dial Program Group List feature by dialing the Abbreviated Dial-Program Group List feature access code, if they have permission to do so.

Reset Shift Dial

The IP DECT system can use reset shift dialing for user controlled call redirection.

Send All Calls

The IP DECT system activates and deactivates the Send All Calls feature for itself by using the send all calls feature access code.

The IP DECT system invokes or cancels Send All Calls for a remote station by dialing the Remote Send All Calls Activation or Deactivation feature access codes. To do this, you must have console permissions assigned to your Class of Service (COS) for the station.

Shuffling (IP direct connections)

The IP DECT configuration supports shuffling whenever the Direct IP to IP Audio Connections field is administered to y on the H.323 Signaling Group screen for X-mobility type of DECT.

SIP - Session Initiation Protocol

The IP DECT system is configured using H.323 IP trunks, not SIP trunks.

Station Firmware Download

The Station Firmware Download feature access code is not applicable, but you can download the firmware to the DECT stations in a different way. The 3720 and 3725 DECT handsets support automatic software download over the air (OTA) in combination with the Avaya In-Building Wireless Server (AIWS).

Station Lock

The IP DECT system locks or unlocks the stations by dialing the Station Lock Activation or Deactivation feature access codes.

Station Security Code Change

The IP DECT system changes their station security code by dialing the Station Security Code Change feature access code.

Team Button

The IP DECT can be a monitored station for the Team Button functionality.

Tenant Partition

An IP DECT station can be restricted to a specific Tenant Partition (TN).

Terminating Extension Group

An IP DECT station can be a member of a terminating extension group (as a primary, not a bridge).

Transfer

When the IP DECT station indicates a flash during a call, it must be treated as initiating a transfer operation. The operation can be a blind or supervised transfer, and includes display updates.

The IP DECT station can be used as the transferor or the transferee for the Transfer Recall feature.

The IP DECT station transfers a call directly to voice mail by dialing the Transfer to Voice Mail feature access code.

Trunks

The IP DECT system initiates a trunk call by dialing a Trunk Access Code (TAC).

The IP DECT station answers a call alerting on night bells by dialing the Trunk Answer Any Station feature access code.

Uniform Dialing Plan

The IP DECT system supports a Uniform Dialing Plan.

User Control Restriction

The IP DECT system changes the restriction levels for a specific user by dialing the User Control Restrict Activation or Deactivation feature access codes. To do this, you must have console permissions assigned to your Class of Service (COS) for the station.

Whisper Page

The IP DECT station sends a whisper page to another user by dialing the Whisper Page Activation feature access code. The IP DECT station can be the recipient of a Whisper Page call, but cannot control the Whisper Page feature through the Whisper Page Off or Answerback feature buttons, as the IP DECT stations cannot support administered feature buttons.