as-needed

The CA-TSC is set up only when needed. This setting causes a slight delay. Avaya recommends this entry for most situations.

at-setup

The CA-TSC is automatically set up for every B-channel call whether or not it is needed.

none

No CA-TSC is set up. This setting permits tandeming of NCA-TSC setup requests.

blank

Indicates that the system does not apply a limit to the number of hops for this preference.

1 to 9

Limits the number of hops if you use the Tandem Hop capability. Valid values are the digits 1 to 9.

1 to 32

Limits the number of hops if you use the Transit capability. Valid values are the digits 1 to 32.

asterisk (*)

When an asterisk (*) is in the route pattern and the outgoing trunk is signaling type mf, the MFC tone for the end-of-digits is sent out to the central office (CO) in place of the asterisk (*).

pound sign (#)

When the pound sign (#) is in the route pattern and the outgoing trunk is signaling type mf, the MFC tone for the end-of-digits is sent out to the central office (CO) in place of the pound sign (#).

comma (,)

A comma (,) uses 2 places. A comma (,) creates a 1.5-second pause between the digits that are sent. Do not use a comma (,) as the first character in the string unless it is absolutely necessary. Misuse can result in some calls, such as Abbreviated Dialing or Last Number Dialed calls, not completing.

plus sign (+)

The plus sign (+) waits for dial tone up to the Off Premises Tone Detection Timer. The system then sends either digits or intercept tone, based on value in the Out Pulse Without Tone field on the Feature-Related System Parameters screen.

percent sign (%)

The percent sign (%) starts End-to-End Signaling.

exclamation point (!)

An exclamation point (!) waits for dial tone without timeout, and then sends dual-tone multifrequency (DTMF) digits.

ampersand (&)

An ampersand (&) waits for Automatic Number Identification (ANI). An ampersand (&) is used for Russian pulse trunks.

p

The associated trunk group must be of type sip. Type the single digit p for fully qualified E.164 numbers. The system translates the p to a plus sign (+). The system then places the plus sign (+) at the front of the digit string.

dollar sign ($)

If ($) sign is in the Inserted Digit String of a routing pattern, the MF Packet does not have ANI information. That is, use 1 S F11 format.

If ($) is not in the Inserted Digit String of a routing pattern, the MF Packet shall have the 1 S Cs def xxxx F11 format.

both

Calls from restricted and unrestricted endpoints can access the route pattern.

rest

Calls from restricted endpoints can access the route pattern.

unre

Calls from unrestricted endpoints can access the route pattern.

Valid carrier code

Identifies the carrier for IXC calls.

user

Identifies a presubscribed carrier. Used when an IXC is not specified.

none

The IXC field must be none for non-ISDN trunk groups and for Bellcore NI-2 Operator Service Access. If you need to send an IXC code for a non-ISDN trunk group, type the IXC code in the Inserted Digits field.

next

Go to the next routing preference and attempt the call again.

rehu

Rehunt within the current routing-preference for another trunk to attempt the call again.

none

LAR is disbled for the preference.

blank

E.164(1)

1-MAX

natl-pub

E.164(1)

national(2)

intl-pub

E.164(1)

international(1)

locl-pub

E.164(1)

local/subscriber(4)

pub-unk

E.164(1)

unknown(0)

lev0-pvt

Private Numbering Plan - PNP(9)

local(4)

levl0-pvt (use this entry to allow Network Call Redirection / Transfer

lev1-pvt

Private Numbering Plan - PNP(9)

Regional Level 1(2)

lev2-pvt

Private Numbering Plan - PNP(9)

Regional Level 2(1)

unk-unk

unknown(0)

unknown(0)

0

• Suppress a user-dialed prefix digit 1 for 10-digit FNPA calls.

• Leave a user-dialed prefix digit 1 for 7-digit HNPA calls.

• Leave a prefix digit 1 on 10-digit calls that are neither FNPA nor HNPA calls.

Do not use Prefix Mark 0 in those areas where all long distance calls must be dialed as 1 plus 10 digits. Check with your local network provider.

1

Send a 1 on all 10-digit calls, but not on 7-digit calls. Use Prefix Mark 1 for HNPA calls that require a 1 to indicate long distance calls.

2

Send a 1 on all 10-digit and 7-digit long distance calls. Prefix Mark 2 uses a Toll Table to define long distance codes.

3

Send a 1 on all long distance calls, and keep or insert the NPA so that all long distance calls are 10-digit calls. The system inserts the NPA when a user dials a prefix digit 1 plus 7 digits. Prefix Mark 3 uses a Toll Table to define long distance codes.

4

Always suppress a user-dialed Prefix digit 1. Use Prefix Mark 4, for example, when the system routes ISDN calls to a media server or a system that rejects calls with a prefix digit 1.

blank

For TIE trunks, leave this field blank.

accunet

i800

inwats

lds

mega800

megacom

multiquest

operator

oper-lds

Operator and lds

oper-meg

Operator and megacon

oper-sdn

Operator and sdn

outwats-bnd

sdn

Enter to allow Network Call Redirection/Transfer.

sub-operator

sub-op-lds

Suboperator and lds

sub-op-meg

Suboperator and megacom

sub-op-sdn

Suboperator and sdn

wats-max-bnd